Product classification
Disposable sterile medical oxygen nebulizer mask (children's type)
hiddenValue
Details Introduction
- Product Description
-
【Product Name】Disposable Sterile Medical Oxygen Nebulizer Mask (Child Type)
【Product Model Specification】See product single packaging
【Scope of Application】For use by medical units in conjunction with medication for nebulization inhalation therapy for patients with respiratory diseases, for single use. The product is provided sterile from the factory.
【Main Structure】Mainly composed of mask and connector, optional nebulization cup, bite mouth, and bent tube.
【Product Performance】
1. Nebulization amount: Under working conditions of 6L/min flow rate, the nebulization amount should meet the clinical requirements for nebulization inhalation medication treatment, and should be ≧0.25mL/min.
2. Equivalent volume particle size distribution: The diameter distribution of the mist particles produced by the nebulizer: the proportion of mist particles with a diameter of 1μm to 5μm should be greater than 60%.
3. The product should be sterile, and the residual amount of ethylene oxide should be ≤10μg/g.【Instructions for Use】
1. Open the packaging, take out the product, and connect the nebulization cup and connector.
2. Rotate and remove the top connector of the nebulization cup, add the corresponding medication according to medical advice (do not exceed the maximum scale line on the cup), and then reinstall the top connector. When installing the top connector, the bottom should not hit the small hole in the middle of the nebulization cup, otherwise it may affect the nebulization effect.
3. Connect one end of the connector to the gas source, place the mask over the mouth and nose or hold the bite mouth in the mouth as needed, turn on the gas source, and slowly inhale and exhale, repeating this step until the medication is fully nebulized.
4. After nebulization is complete, turn off the gas source, disconnect the connector from the gas source, and properly dispose of the nebulization device.【Contraindications】
1. Not suitable for those who are contraindicated for nebulization inhalation therapy.
2. Use with caution for those allergic to PVC material.【Precautions, Warnings, and Advisory Content】
▼ This product is for single use only, and should be disposed of as medical waste after use. This product is sterilized and should not be used if the packaging is damaged.
▼ During nebulization, follow medical advice to use clinically approved recommended nebulization medications.
▼ This product should be purchased and used under the guidance of medical personnel; prevent infants, individuals with mental illnesses from touching it during storage or use; do not place or carry when there is medication in the medication cup.
▼ The applicable population for this product is adults and children who require nebulization inhalation therapy. When used by children, ensure that medical personnel or guardians are present.
▼ Read the instructions carefully before use and ensure it is used within the validity period.
▼ Choose the appropriate model specification based on the patient's actual condition.
▼ This product cannot be sterilized with high temperature or high pressure.
▼ Disposal method after product use: Dispose of as medical device waste.
▼ This product's PVC material (mask, connector) meets EU environmental standards (free of phthalates, i.e., free of 6P), and meets medical grade USP level 5 and above.
▼ Recommended operating pressure is 60kPa-130kPa, gas flow 6L/min-12L/min.【Storage and Transportation Conditions】This product should be stored in a clean indoor environment at a temperature of 0-55℃, relative humidity not exceeding 80%, and free from corrosive gases, with good ventilation. During transportation and storage, prevent moisture, heat, and direct sunlight.
【Production Date】See product single packaging
【Shelf Life】Three years from the date of sterilization
Key words:
Hand Hygiene Disinfection | Skin and Mucous Membrane Disinfection
Product Consulting
Note: Please leave your email and our professionals will contact you as soon as possible!
Address: Building 12, Changgui ASEAN Science Park, 146 Wuhua Avenue, Guangxi ASEAN Technology Development Zone
Nanning Office: 4th Floor, Block C, Yongjia Building, Xinmin Road, Qingxiu District, Nanning City